Spellbinders Machines & Accessories

Grand Calibur - Personal die cutting machine complete with the cutting and embossing plates needed to get started and basic instructions. The machine needs the handle pressed onto the shaft when it comes out of the box (no tools required) and can be removed again to store back in the box if desired. There is a suction cup to anchor the machine to a smooth table which releases with a lever. You will need dies or an embossing folder as there are none supplied with it
The machine will cut and emboss up to 215mm (8.5") width and comes with the following 8.5" x 12" sized plates: Base Plate A - Embossing Plate B - Cutting Plate C - Tan Rubber Mat. With use these will become marked and will have to be replaced when both sides have been used until they no longer cut neatly.
To operate it simply requires the right combination of mats, dies and folders which are fed into the mouth of the machine and wound through with the handle.
Sizzix dies cannot be used with this machine.

Note: From January 2012 the maximum width of the Grand Calibur was extended to take 8.5" and all the new plates and accessories are changing to reflect this. Older machines can take the new size but require you to remove the feed tray, this makes it a little more difficult to use but, if you purchase the replacement plates pack at the new size they have included a new tray to update your machine.

ImageCode & DescriptionPriceQty 
SBGC001
Spellbinders Grand Calibur - Teal
£99.99 Add Singles
Spellbinders Tool 'N one - This handy tool is a brush, pricking tool and shape removal tool in one. It is made from plastic with a brush at one end and the pricking tool at the other, a spatula removal tool is in the pack. The ends are sprung loaded, pull them down to remove one tool and insert the other, the centre unscrews and the pricking tool and spatula can be stored inside. The brush helps remove all the little bits left in the die after cutting and the spatula helps remove the cut shape from the die, the pricking tool can be used to add extra detail (holes) to the cut outs.
ImageCode & DescriptionPriceQty 
SBT001
Spellbinders Tool N One
£10.99 Add Singles
Replacement Plates - Spare plates for the Grand Calibur machine. This pack includes Base Plate A, Embossing Plate B, Cutting Plate C and a tan embossing mat. These are the 8.5" x 12" size so your A4 will fit with a few millimetres to spare.

Note: - In January 2012 the Grand Calibur was updated to be able to take an 8.5" sheet as standard (they used to take A4 at 8.25"), though they could be used for wider by removing the feeder tray. The older machines are able to take and work with the new size plates but need a new tray for easy use. This pack contains one tray at the new size.

ImageCode & DescriptionPriceQty 
SBGC007
Grand Calibur Replacement Plates With Tray 8.5 X 12 Inches
£23.99 Add Singles
Spellbinders Grand Claibur Cutting Plate - Replacement cutting plates (plate C) for use with the Grand Calibur machine. See the individual listing for the sizes.
ImageCode & DescriptionPriceQty 
SBGC004
Grand Calibur Cutting Plate - 8.25 X 11.75 Inch
£9.99 Add Singles
SBGC005
Grand Calibur Cutting Plate - 8.5 X 12 Inch
£9.99 Add Singles
Grand Calibur and Grand Calibur Junior Raspberry Spacer Plate - Spacer/adaptor plate (plate D) for the Grand Calibur. This is required when using M-bossabilities embossing folders.
ImageCode & DescriptionPriceQty 
SBGC008
Grand Calibur Raspberry Adaptor Plate - 8.5 X 12 Inch
£9.99 Add Singles
SBGC012
Grand Calibur Junior Raspberry Spacer Plate - 8.5 X 6 Inch
£6.99 Add Singles
Grand Calibur and Grand Calibur Junior Rubber Mat - Rubber embossing mats. The Junior refers to the size, they are smaller than usual to make using small size dies less laborious.
ImageCode & DescriptionPriceQty 
SBGC006
Grand Calibur Grand Rubber Mat - 8.5 X 12 Inch
£9.99 Add Singles
SBGC010
Grand Calibur Junior Rubber Mat - 8.5 X 6 Inch
£7.49 Add Singles
Grand Calibur Junior Replacement Plate Set - This is a set of plates for use with the Grand Calibur, they are the same as the usual plates but at a smaller size, useful when cutting small dies as, being smaller, there is less winding through of the empty plates. Set consists of Plate A, Plate B, Plate C and the tan embossing mat.
ImageCode & DescriptionPriceQty 
SBGC011
Grand Calibur Junior Replacement Plates - 8.5 X 6 Inch
£19.99 Add Singles
Grand Calibur Junior Metal Shim - A metal shim to be used with some products, see details taken from the manufacturers website:

The Junior Metal Shim is to be used in the Grand Calibur® Die Cutting and Embossing Machine (NOTE: Not for use with the Spellbinders Artisan X-plorer™ Machine). Great for not only cutting metals but for cutting those intricate designed die templates. Cut and emboss sandwiches for our Grand Calibur Machine are as follows: Cutting Sandwich (stack from bottom to up): 1. Spellbinders Base Plate A; 2. Junior Metal Shim; 3. Medium; 4. Die Template (cut ridges down); 5. Either Pink Embossing Plate or Raspberry Spacer Plate (depending on thickness of sandwich) NOTE: Do NOT use with Imperial Gold dies – debossing designs will cut through. Do NOT use white cutting plate with the Junior Metal Shim.

ImageCode & DescriptionPriceQty 
SBGC016
Grand Calibur Junior Metal Shim - 8.5 X 6 Inch
£9.99 Add Singles
Spellbinders Junior Magnetic Placement Mat - Flexible, magnetic sheet which will hold your cutting dies in place while you cut. Mat measures 152mm x 215mm and is for use on the Grand Calibur with Imperial Gold die templates.
ImageCode & DescriptionPriceQty 
SBGC015
Spellbinders Junior Magnetic Placement Mat
£7.49 Add Singles
Embossing Pads - Two tan rubber embossing mats for the Wizard, measuring 130mm x 175mm. These are used to emboss spellbinders dies in most manual cutting machines.
ImageCode & DescriptionPriceQty 
SBW023
Embossing Pads
£7.99 Add Pack 02
Grand Borderabilities Pack - A set of cutting and embossing plates for use with the Grand Borderabilities dies. Contains 2 Cutting mats at 75mm x 354mm, 1 Embossing pad at 75mm x 310mm and 1 Magnetic spacer plate at 75mm x 318mm.
For use with the Wizard machines only.
ImageCode & DescriptionPriceQty 
SBW026
Grand Cut Mat Kit
£18.99 Add Singles
Extended Cutting Mats - A pack of 2 cutting mats which are a little larger than the standard ones. These measure 150mm x 220mm.
For use with the Wizard Machines (thicker than those for the Grand Calibur).
ImageCode & DescriptionPriceQty 
SBW022
Extended Cut Mats
£15.99 Add Singles
Return to top
Craft Creations Limited, Ingersoll House,
Delamare Road, Cheshunt, Hertfordshire, EN8 9HD, UK
Tel: 01992 781900 - Fax: 01992 634339
Bookmark and Share